Skip to main content

Materials Science interviews

Materials Science interview questions: turn every choice into a trade-off

16 sections4,011 words21 min read5 official sources

What the format looks like

The course page says you will be invited to an applicant day if your UCAS application indicates you are likely to satisfy the requirements. Applicant days run on Wednesdays between November and March from 10.30 to 15.30, and you are expected to stay the whole day: talks from the Director of Undergraduate Studies and the Admission Tutor, then a 30 minute one-to-one interview, a 45 minute engineering group task and a 45 minute Q&A with student ambassadors. Imperial’s central page adds that interviews usually fall between November and February, may be virtual or in person, and that the department contacts you itself. Whether you are invited, when and in what form is the department’s decision; the ten problems below are original practice, not the questions of that day.

Reading zoom
Part 1

What the applicant day actually is

It is called an applicant day, not an interview day: after talks from the Director of Undergraduate Studies and the Admission Tutor come a 30 minute one-to-one with a lecturer, a 45 minute group task, “an engineering-based problem-solving challenge to see your team working skills”, and a 45 minute Q&A with student ambassadors, on a Wednesday from 10.30 to 15.30.
Two things follow. You are under observation far longer than thirty minutes, since the group task and the student session count too. And the day runs both ways: the page says the one-to-one is as much for you to decide whether Imperial suits you as for them to judge you.
01Listen with a pen

Two talks

These talks are not background noise; every question you ask later stands on them.
02

The 30 minute one-to-one

It opens on your statement and interests, then follows your answers instead of a card of set questions.
03The longest observable block

The 45 minute group task

Nobody is credited for solving it alone; what is noticed is who fixed the brief and who built on another’s idea.
04

The 45 minute student Q&A

An open session with ambassadors, where you settle what the four years actually involve.
Part 2

With no test, what the day has to carry

Imperial says most departments interview applicants who show potential in their UCAS application “and in an admissions test (where this applies)”. Materials sits in the does-not-apply column, so what is left is the form itself, results gained and predicted, the referee’s report, and what you do on the day.
Three consequences. Your statement carries more weight, which is why the first published tip is to reread it. Nothing compensates for a shaky corner of your foundation, and nothing has to explain it either. And the group task is fresh evidence that appears in no standardised document. In our sessions a two hour rehearsal is split forty minutes one-to-one, thirty minutes on the team task, the rest reviewing the recording.
The ten problems here are original interview practice written by Frontier Academy for the applicant day. What you are asked depends on how you answer, so prediction is useless; what you can train is starting to speak, showing your working and using the follow-up.
Part 3

What a lecturer is judging in thirty minutes

“More of a conversation” is about format, not politeness: there is no shared question card, and the lecturer follows wherever your answer goes. In our sessions we sort what can be observed into four things. Property language: can you trade “use aluminium here” for “stiffness per unit mass dominates, because self-weight sets the life”. Visible assumptions: do you read out your numbers before the conclusion. Redirection: a condition gets added, hotter, more cyclic, cheaper, weldable, and the signal is whether you re-run the reasoning. Why you: whether you are taken by the word “materials” or chased by “why did this part fail”.

Course fit

Can you name the kind of problem you want to work on

Visible method

Property and assumption first, conclusion second

Coachability

Do you change course when a condition changes

Two-way judgement

The questions you ask are evidence too

Part 4

How to rehearse a 45 minute group task

Group tasks fail in a few familiar ways, rarely for lack of skill. The commonest is four people calculating in silence until the clock runs out with two incompatible answers. Next is one person talking throughout while the rest become an audience, which reads badly when the stated purpose is team working. Third is discussion that never lands, since a proposal needs a sketch, a few numbers and a reason.
Our rehearsal rules are three: write the requirements on one line before anyone calculates; circulate one sheet, with each idea stated in a sentence and repeated back by someone else; and stop in the last five minutes to settle who presents and how you answer “why this”.
01

Opening with a solution

Wrong
“Let us just use carbon fibre.”
Right
“Three requirements first, then two candidates against them.”
Spot it:
Nobody can build on your idea because the target was never written down.
02

Finishing every sentence

Wrong
“I have finished, do it my way.”
Right
Push the paper to the middle and ask where everyone else got to.
Spot it:
At the end the group has only your answer to present.
03

Calculating in silence

Wrong
Four heads down for forty minutes.
Right
Look up halfway and read the interim result so the group re-syncs.
Spot it:
Whoever presents cannot say where the number came from.
04

Agreement that is not agreement

Wrong
“Whatever, yours is fine.”
Right
“I am unsure about that assumption. Can we spend two minutes testing it?”
Spot it:
The disagreement has not gone away, it has only gone underground.
Part 5

The numbers, and how this differs from Oxbridge

Start with the fixed information. The A-level minimum standard is AAA, with an A in Maths, an A in Chemistry or Physics and a third useful subject, and the typical offer is stated as A*AA; the IB minimum is 38 points with 6 at Higher Level in Maths and in Physics or Chemistry, 39 typical; the UCAS codes are JFM2 and I50; the equal-consideration deadline is 18.00 UK time on 13 January 2027; and the course sits inside the ATAS scheme under code CAH10-03-02.
Two readings matter. The deadline is in mid-January, so the department reads you while your A levels are nowhere near finished, which is why questions 1 and 8 deserve the earliest work. ATAS and the course code are administration and change nothing about what you are asked. And Imperial’s event is a full day on site, given as 10.30 to 15.30, while Oxford and Cambridge run half-hour subject conversations.

A-level minimum

AAA with an A in Maths and an A in Chemistry or Physics, plus a third subject; typical offer A*AA

IB

Minimum 38 points with 6 at Higher Level, 39 typical

UCAS codes

Course JFM2, institution I50

Deadline

13 January 2027 at 18.00 UK time

ATAS

Subject code CAH10-03-02

Admissions test

The department uses no test

DimensionImperial MaterialsOxfordCambridge
WhenApplicant days on Wednesdays, November to MarchDecember 2026, onlineMain period 7 to 18 December
Live componentsA 30 minute one-to-one, a 45 minute group task and a 45 minute student Q&AAcademic discussions of your subject; many applicants have more than oneUsually one or two, 35 minutes to an hour in total
Admissions testNo test used by this departmentDepends on the course; see the subject’s own pageDepends on the subject; some add an assessment around the interview

Oxbridge dates come from the two universities’ published interview pages and the Imperial dates from the Materials course page. All three institutions assess independently; this table compares published formats only, not difficulty or chances.

Part 6

How to use these ten problems, and the official checklists

015 to 8 min

Try it alone, timed

Write every route you can see, including the failed ones, and mark the step where you stopped.
02

Say it aloud in English

Record three minutes in English and ask one thing on playback: could anyone follow this without the paper?
03The step that matters

Have someone push back

Ask someone outside your subject to use two lines only: why that assumption, and what if you heat it.
04

Change a condition and redo it

Swap single loading for cyclic and room temperature for three hundred degrees; if nothing moves, you missed the dependency.
Imperial’s own tips, converted into actions
Imperial’s tips are reread your statement, since follow-ups come from what you wrote; take a school mock interview; practise body language and concise answers; arrive early; prepare questions; keep your invitation; no dress code. Our order is statement audit first, speaking practice second, logistics last.
Turn your personal statement into a map of follow-ups
Copy out every “I am interested in X” and attach three things: a detail only you would know, one record of changing your mind, and one question you cannot answer. Cut the sentence that cannot produce the third, because the interviewer drills three levels into whatever you genuinely know.
Online or in person: the email decides
The course page describes a full day while the central page allows virtual or in person, so go by the invitation you received. If it is online we add three things: camera at eye height, paper on the desk rather than a phone, and an early login with a backup connection, plus one rehearsal of writing where a camera can see it.
Original practice

10 Materials Science interview problems

Every problem below is original practice written for this site. Read the question, try it aloud, then compare your reasoning with the approach.

01Question 1
Why materials rather than mechanical or chemical engineering? And what in this course specifically feels essential to you?
Frontier ACE mock practice4 steps
  1. What it tests
    The department describes the thirty minutes as a conversation whose job is to judge whether you suit the course, so the opening question is not small talk. The lecturer is listening for one checkable signal: can you state the difference between these three routes, or only that you like science? The course requires Maths alongside Chemistry or Physics, which is the crossover it is aiming at, and you need to fit that shape out loud.
  2. 1
    Step 1
    One sentence for the entrance: the experiment or the broken object that started it. Skip the background and name the scene.
02Question 2
Why is a phone screen made of glass? Name one property you accept losing because of that choice, and then tell me what you would change.
Frontier ACE mock practice4 steps
  1. What it tests
    This tests how a materials selection is actually made: list the properties that fight each other, then admit what you gave up. Saying “glass is hard and scratches less” just recites common sense; the interviewer wants to see you put transparency, hardness, fracture toughness, cost and repairability on one table and weigh them.
  2. 1
    Step 1
    Start with what the object meets daily: grit in a pocket (hardness and scratching), impact on the floor (shock and crack growth), skin contact (surface energy and fingerprints), and the need to transmit light.
In winter, pouring boiling water into a cold ceramic mug can crack it, while a metal kettle will not. Why?
Frontier ACE mock practice4 steps
  1. What it tests
    This tests the chain from structure to properties: expansion, the temperature gradient conduction creates, and the fact that ceramics are weak in tension with almost no plasticity. The interviewer is listening for where the stress comes from and why the material cannot shed it by deforming, not for the word “brittle”.
  2. 1
    Step 1
    Start with the inside heating first: the inner wall wants to expand, the cold outer wall refuses, so the inside goes into compression and the outside into tension. Saying which surface is loaded which way shows the thinking better than any formula.
Estimate how much copper is used in the electrical wiring of an ordinary three-bedroom house. Narrate every move as you make it.
Frontier ACE mock practice4 steps
  1. What it tests
    This tests estimation habits: do you decompose the object, do you keep units, do you convert volume to mass through a density, and above all do you read your assumptions out loud. The interviewer is not checking accuracy, they are checking whether you can sanity-check yourself.
  2. 1
    Step 1
    Decompose before numbers: copper sits mainly in the fixed wiring (socket and lighting circuits), the consumer unit and inside appliances. Pick the biggest single block and start there, not the hardest.
Here are four materials as Young’s modulus in GPa, tensile strength in MPa and density in g per cubic centimetre: A is 3, 60, 1.2; B is 70, 300, 2.7; C is 200, 400, 7.8; D is 130, 1500, 1.6. Which would you choose for a bicycle frame?
Frontier ACE mock practice4 steps
  1. What it tests
    This tests your first move with data: do you ask which quantity the task is minimising. On a frame, weight sets the cost of accelerating and climbing, so the numbers to compute are stiffness per unit mass and strength per unit mass, not simply the largest modulus. The interviewer is also listening for whether you do the division out loud and whether you name the columns missing from the table.
  2. 1
    Step 1
    Write the objective as two or three ranked lines: it must not flex under load (stiffness), it must survive a crash (strength and toughness), and it must be light (density). Say which one you put first, because every later step hangs on that.
06Question 6
Carbon fibre is light and strong, and people often call it the green choice. If a sports component or a turbine blade is carbon-fibre composite, what are your real options when it retires?
Frontier ACE mock practice4 steps
  1. What it tests
    This tests life-cycle reasoning: can you split “green” into three separate accounts, being energy, performance and feasibility, and can you admit that the value of recycling depends on how long the part served. Shouting “it is recyclable” dodges the question; the interviewer wants you to say plainly what downcycling means.
  2. 1
    Step 1
    Start with where the value sits: carbon fibre buys stiffness and strength per unit weight. Any recovery route that shortens the fibres or damages the interface takes the material out of its original duty.
07Question 7
In the 45 minute group task, your four-person group has been working for twenty minutes. One member has not spoken at all and another insists your direction is wrong. What do you do?
Frontier ACE mock practice4 steps
  1. What it tests
    This maps directly onto the element the course page describes: an engineering problem-solving challenge used to see your team working skills. So the answer cannot be “I am a good communicator”; it has to be executable behaviour: the specific question that gets the quiet person talking, and the method that converts a disagreement into a testable assumption.
  2. 1
    Step 1
    Stop calculating and restate the brief to the group in one sentence: what we are being asked, what we must hand over, how much time is left. This re-aligns everyone and gives the quiet member a zero-cost way in.
08Question 8
You mention a project you did. Take me through the worst thing that went wrong in it: what did you decide at the time, and what have you changed since?
Frontier ACE mock practice4 steps
  1. What it tests
    Imperial’s first published tip is to reread your personal statement, with follow-ups built from what you wrote. In this question the lecturer is verifying two things at once: whether you actually did it, through the dated and quantified details, and whether you can admit the limits of your own method. A project with nothing wrong in it tends to be pushed until it breaks.
  2. 1
    Step 1
    Tell the whole timeline in sixty seconds using three sentences: what I first believed, when the numbers started disagreeing, when I admitted it. Do not turn a small failure into a thirty-minute epic.
Metals and semiconductors both conduct, but heat them up and their resistance moves in opposite directions. Explain why using the simplest picture you can.
Frontier ACE mock practice4 steps
  1. What it tests
    The course wants Chemistry or Physics alongside Maths, so boundary questions like this appear. It tests whether one model can explain two families: in one, heating changes how often carriers are scattered; in the other, it changes how many carriers there are. The interviewer is also listening for whether you say honestly which part you have not been taught.
  2. 1
    Step 1
    Finish the metal first: plenty of free electrons, and heating makes the positive ions vibrate harder, so electrons are scattered more often, the mean free path shortens and resistance rises. No formula needed; the picture has to be clear.
10Question 10
Before the day ends you have 45 minutes with current students and you can ask us things too. What would you ask?
Frontier ACE mock practice4 steps
  1. What it tests
    The day is built to be two-way: the department says the one-to-one is as much for you to judge Imperial as for them to judge you, and thinking of questions to ask is one of the published tips. So this is not a courtesy at the end. It shows how far your thinking has gone: asking something the course page already answers is a different level of preparation from asking how a student actually changed over four years.
  2. 1
    Step 1
    Open by naming what you will not ask and why: entry requirements and course structure are on the course page and you have read them. That sentence on its own is evidence of preparation.

drag the windows

Frontier ACE · sample question (live)

Practise this question on Frontier ACE

A timed preview: read the question, think for a few seconds, then answer aloud. Frontier ACE scores the attempt on five dimensions.

Open the sample question
Scores

KEY NUMBERS

80/ 100

Tech×3582
Struct×2074
Relev×2088
Engage×1570
Deliver×1079
Full report

Sister site

Practise saying the thinking out loud

Frontier ACE is Frontier Academy’s AI interview practice site for Oxford, Cambridge and Imperial applicants. It runs timed video-style practice and mock interviews, then scores each attempt on five dimensions. Use it to rehearse the conversation, then come back to the subject problems here.

Frontier ACE is a Frontier Academy site. Links open in a new tab and are tagged as referrals.

Sources

Official sources

5 official sources (click to view)
FAQ

Frequently asked questions

Does Materials Science and Engineering need an admissions test?
No. The course page states that “this department does not use a test as part of its selection process”, and Materials appears as no-test on the department table; ESAT belongs to the departments listed in our ESAT guide.
Do I have to stay the whole applicant day, and what happens in it?
Yes. Applicant days run on Wednesdays between November and March from 10.30 to 15.30 and you stay all day: two opening talks, a 30 minute one-to-one, a 45 minute group task and a 45 minute student Q&A. The last two belong to the assessment, not to the waiting time.
If I am not invited to an applicant day, is that the end of it?
Not necessarily. Imperial says most departments interview applicants who demonstrate potential, and the course page keeps its wording conditional. No invitation or offer rate is published, so figures of that kind are not official information.
I know nothing about the front edge of materials. Should I do some reading?
Yes, but not to look knowledgeable. We push one piece of reading until you can name a question you cannot answer, because an interviewer follows your reading three levels down and the third level is usually what you make of it.
What is ATAS, and must I sort it out before the interview?
The course page gives ATAS subject code CAH10-03-02. ATAS is a UK screening exercise applying to some courses and nationalities; it is not extra subject preparation and it does not change what you are asked. Handle it after the invitation using official guidance.

UAT-UK, Pearson, OCR, the University of Cambridge, Imperial College London and other names and logos belong to their respective owners.

Next: Materials Science interview practice

Work through all 10 problems aloud, then rehearse a full interview with FrontierACE. Both are built by Frontier Academy.